********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.2.2 (Formal Release) Release Date : 22nd November 2016 Build Date : 13th October 2016 Revision : r6591 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** IMPORTANT NOTE: Do not upgrade directly from 1.0.5 (and earlier) to 1.2.2. Due to differences in the Web UI and functionality the router MUST first be upgraded to at least 1.0.7.1 prior to upgrading to 1.2.2 Upgrade your router to Version 1.0.7.1 or later first, and afterwards upgrade the router to Version 1.2.2 [New Features] None. [Improvement] 1. FTP connections in Active mode were not passed correctly through NAT 2. When using [Diagnostics] > [Data Flow Monitor] > Packet Monitor, results could not be filtered by Host 3. Resolved an issue that could cause higher than normal memory usage with some router configurations 4. When configuring a User Management profile for VPN with MOTP enabled, it could not be saved without entering a password 5. TTL values were reported incorrectly in the [Diagnostics] > [Session Table] 6. Improved connectivity for Mac OS X SmartVPN clients [Known Issue] 1. High Availability - Updating from a firmware version <=1.1.0.2: Due to significant changes to High Availability functionality, existing HA configuration will be cleared during the update process and it will be necessary to reconfigure High Availability after the update 2. Disable "Force IPsec with L2TP" option in [VPN and Remote Access] > [PPP General Setup] to allow a standard L2TP tunnel, otherwise the L2TP server will allow L2TP with IPsec only 3. F/W 1.2.0 onwards Changes the behaviour of the IP Filter. After upgrade some IP Filter rules may need to be reconfigured. Please read the "Filter Rule Actions" segment of this guide for more information on the changes: http://www.draytek.co.uk/support/guides/kb-3900-ipfilter-basics ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.2.1 (Formal Release) Release Date : 7th September 2016 Build Date : 24th August 2016 Revision : r6454 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** IMPORTANT NOTE: Do not upgrade directly from 1.0.5 (and earlier) to 1.2.1. Due to differences in the Web UI and functionality the router MUST first be upgraded to at least 1.0.7.1 prior to upgrading to 1.2.1 Upgrade your router to Version 1.0.7.1 or later first, and afterwards upgrade the router to Version 1.2.1 [New Features] 1. The router's Online Status can display "Remote DSL" information from a Vigor 130 or Vigor 120v2 modem connected to the router's WAN ports 2. Support WAN Load Balance by Session, configured in [Routing] > [Default Route], the default is IP-based Load Balancing 3. Packet Monitor facility added to [Diagnostics] > [Data Flow Monitor] to capture WAN/LAN packets and download as a .pcap file 4. Web Content Filter Query Server can now be specified in [Objects Setting] > [Web Category Object] > [Query Server] tab [Improvement] 1. NAT efficiency improvements 2. SSL VPN supports Idle Timeout and Reconnect 3. APP-Enforcement Signature updated to improve handling of: IM-Google Hangouts Protocol-DNS HTTP SSL/TLS Tunnel-Ultrasurf VoIP-RC WebHD-HTTP_Upload 4. Web interface response time improved when displaying large numbers of Profiles (User Profile, IP Objects, etc) 5. Improved TCP SYN+FIN filtering mechanism 6. Auto DDoS defense added to reduce CPU load if DDoS occurs [Known Issue] 1. High Availability - Updating from a firmware version <=1.1.0.2: Due to significant changes to High Availability functionality, existing HA configuration will be cleared during the update process and it will be necessary to reconfigure High Availability after the update 2. Disable "Force IPsec with L2TP" option in [VPN and Remote Access] > [PPP General Setup] to allow a standard L2TP tunnel, otherwise the L2TP server will allow L2TP with IPsec only 3. F/W 1.2.1 Changes the behaviour of the IP Filter. After upgrade some IP Filter rules may need to be reconfigured. Please read the "Filter Rule Actions" segment of this guide for more information on the changes: http://www.draytek.co.uk/support/guides/kb-3900-ipfilter-basics 4. FTP connections do not work in "active" mode, "passive" mode works normally. This will be fixed in the next firmware release. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.2.0 (Formal Release) Release Date : 29th December 2015 Build Date : 3rd December 2015 Revision : r5723 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** IMPORTANT NOTE: Do not upgrade directly from 1.0.5 (and earlier) to 1.2.0. Due to differences in the Web UI and functionality the router MUST first be upgraded to at least 1.0.7.1 prior to upgrading to 1.2.0. Upgrade your router to Version 1.0.7.1 or later first, and afterward upgrade the router to Version 1.2.0. [New Features] 1. CPU, Memory, Traffic Tx/Rx usage added to [Notification Object], configured under Advanced Setting tab 2. [Configuration Backup] > [Analysis] displays details of router configuration on one page 3. Auto Firmware Upgrade and Auto Firmware Patch now available to simplify update process 4. [User Management] > [Web Portal] new features: Can use SMS as an authentication method (requires internet SMS provider configured) Option to block mobile devices if required Customise login & background images in Portal Page Setup 5. MAC/Vendor Object now supported for use with IP Filter 6. SMB Server now available under [USB Application] menu for file sharing of connected USB storage 7. Now supports SHA2_256 for IPsec VPN tunnel authentication 8. SSL VPN port can now be configured as a separate port from HTTPS Management under [System Maintenance] > [Access Control] [Improvement] 1. Improvements to the design and functionality of [Applications] > [High Availability] 2. Corrected an issue with Port Redirection which could occur after upgrading to 1.1.x firmware 3. [Firewall] > [Filter Counter] indicates how many sessions have matched each rule 4. General improvements to [Firewall] menus and syslog output 5. Improvements to HTTPS filtering when using Web Content Filtering 6. Specify Remote IP / Host Name to limit Remote Dial-In VPN connections to that WAN IP / Hostname only 7. Bandwidth Limit can now apply to PPTP Remote Dial-In VPN clients 8. [Diagnostics] > [ARP Cache Table] now has an option to quickly create an IP Object for listed IP address 9. Supports Suffix Type in IPv6 Object configuration 10. Time Schedule in Filter Rules can now force sessions to clear when the schedule takes effect 11. Spotify can now be blocked with the Application Filter 12. Can specify which WAN interfaces can be used for remote management 13. Improvements to Traffic Graph and Data Flow Monitor 14. QoS Class was not displayed in the Session Table 15. Support for "esendex" SMS Provider 16. Custom SMS Provider option to define API settings manually for SMS providers not listed 17. Improved the SOA Serial Format for Inbound Load Balance DNS response 18. External Devices can now list up to 200 items [Known Issue] 1. Due to significant changes to High Availability functionality, existing HA configuration will be cleared during the update process and it will be necessary to reconfigure High Availability after updating to 1.2.0 2. Disable "Force IPsec with L2TP" option in [VPN and Remote Access] > [PPP General Setup] to allow a standard L2TP tunnel, otherwise the L2TP server will allow L2TP with IPsec only 3. F/W 1.2.0 Changes the behaviour of the IP Filter. After upgrade some IP Filter rules may need to be reconfigured. Please read the "Filter Rule Actions" segment of this guide for more information on the changes: http://www.draytek.co.uk/support/guides/kb-3900-ipfilter-basics ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.1.0.1 (Formal Release) Release Date : 9th September 2015 Build Date : 27th August 2015 Revision : r5461 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** IMPORTANT NOTE: Do not upgrade directly from 1.0.5 (and earlier) to 1.1.0.1. Due to differences in the Web UI and functionality the router MUST first be upgraded to at least 1.0.7.1 prior to upgrading to 1.1.0.1. Upgrade your router to Version 1.0.7.1 or later first, and afterward upgrade the router to Version 1.1.0.1. [New Features] None. [Improvement] 1. Corrected an issue that could cause Port Redirection to not work after upgrading the firmware from 1.0.9 or earlier 2. Syslog to USB was not writing to USB after restarting the router 3. It was not possible to modify the max failed Telnet Login attempts before the router bans the IP 4. Netbios names were not displaying in the ARP cache table correctly 5. Improvements to certificate handling for the router's HTTPS interface 6. DNS Suffix (DHCP Option 15) support added for remote dial-in VPN clients 7. Upgraded OpenSSL to 0.9.8zg for security updates 8. Resolves an WAN connectivity issue that could occur after after an extended duration [Known Issue] 1. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in [VPN and Remote Access] > [PPP General Setup]. 2. The upgrade may affect Port Redirection entries if the router's configuration has been upgraded from 1.0.7.1 or previous firmware. To resolve this issue, please use 1.2.0 r5508 beta firmware. If the router has been factory reset or was installed with 1.0.8 or later firmware, port redirection will work normally. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.1.0 (Formal Release) Release Date : 6th August 2015 Build Date : 24th July 2015 Revision : r5322 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** IMPORTANT NOTE: Do not upgrade directly from 1.0.5 (and earlier) to 1.1.0. Due to differences in the Web UI and functionality the router MUST first be upgraded to at least 1.0.7.1 prior to upgrading to 1.1.0. Upgrade your router to Version 1.0.7.1 or later first, and afterward upgrade the router to Version 1.1.0. [New Features] 1. SSL VPN LAN to LAN tunnel (Supported from DrayTek Vigor 2960 / 3900 1.1.0 firmware and Vigor 2860 / 2925 3.8.x firmware). 2. Internal RADIUS server under [User Management] > [RADIUS]. 3. APP Enforcement supported app list added under [Objects Settings] > [APP Support List]. 4. Added auto/manual APP Signature Upgrade setting page in [System Maintenance] > [APP Signature Upgrade]. 5. [System Maintenance] > [Access Control] Improvements: Validation Code in Access Control tab to improve web admin security; Fail to Ban setting page to automatically block IP addresses after failed login attempts; Access Barrier setting page to protect router services (WUI, FTP etc) from brute force attack. 6. Added Switch Rate Limit setting page in [Firewall] > [Dos Defense]. 7. Added [NAT] > [Connection Timeout] to allow altering the session timeout of different traffic types i.e. TCP, UDP etc 8. Wake on LAN can now operate on a schedule by configuring profiles in [Applications] > [Wake on LAN] > [Schedule Wake on LAN] 9. [Diagnostics] > [MAC Address Table] added. 10. [Diagnostics] > [User Status] added, to show PPPoE / Web Portal / VPN / SSL Proxy users in one location. 11. [LAN] > [LAN DNS] now supports wild-card strings and CNAME records for individual LANs using the Specified LAN option. 12. [Routing] > [Policy Route] Improvements: Priority options (Normal, High, Top) for more flexible routing. Country Objects as destination addresses. Failover options for target IP ping failure. 13. Support for Multicast via VPN. 14. Router's web interface can now notify of new firmware upgrades available. [Improvement] 1. Improved DDoS protection. 2. SSL VPN settings now available under [VPN and Remote Access] > [PPP General Setup]. 3. PPTP Dial-In VPN Profile (LAN to LAN) now supports multiple remote subnets. 4. LDAP/RADIUS support for the router's SSL Proxy facility. 5. [User Management] > [Web Portal] > [Portal Page Setup] now supports uploading an HTML file as the bulletin message. 6. Packet Inspection settings added under [Firewall] > [Filter Setup] > [Default Policy] 7. [User Management] > [User Profile] > [Apply All] improved to allow multiple choice. 8. Port Statistics now shown under [Diagnostics] > [Traffic Statistics]. 9. Session Information added to [Diagnostics] > [Traffic Graph]. 10. Vendor Information added to [Diagnostics] > [ARP Cache Table]. 11. Daily / Period timout settings added to Web Portal under [User Management] > [Web Portal] > [General Setup]. 12. Bind IP to MAC can now be applied to specific subnets. 13. Supported added for VPN routing through GRE over IPSec tunnel (VPN Trunk). 14. Keep VPN Setting option added to [Central VPN Management] > [CPE Management]. 15. Alert interval of temperature sensor now configurable under [USB Application] > [Temperature Sensor] > [General Setup]. 16. The router could not use a DNS server located on the LAN for DNS queries under some circumstances. 17. Traffic was unable to pass between LAN and PPPoE server clients. 18. Web Content Filter category selection page improvements. 19. IP Filter now shows a counter display for matched packets. 20. Policy Route increased to 120 entries, Static Route increased to 200 entries. [Known Issue] 1. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in [VPN and Remote Access] > [PPP General Setup]. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.9.1 (Formal Release) Release Date : 16th February 2015 Build Date : 2nd February 2015 Revision : r4765 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] None. [Improvement] 1. The IGMP Proxy feature's compatibility with some ISPs that use PPPoE has been improved. 2. Support for the Bandluxe C330 USB 3G modem. 3. SSL VPN now changes tunnel MTU in relation to the WAN MTU. 4. PPTP Dial-In User VPN connections could not access the internet under some circumstances. 5. Policy Route was not working with return path traffic. 6. The IPsec option "Auto Dial Out if WAN1 Down" was still taking effect after being disabled in the WUI. 7. The router's memory usage was higher than normal when using the Data Flow Monitor. 8. The Access Control List was not working correctly under some circumstances. 9. Improvements to ensure immunity to Ghost/CVE-2015-0235 [Known Issue] 1. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in VPN and Remote Access >> PPP General Setup. 2. VPN Trunk tunnel should not be used with a profile name over 15 characters. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.9 (Formal Release) Release Date : 24th December 2014 Build Date : 1st December 2014 Revision : r4542 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] 1. Supports USB 4G/LTE. Check [USB]-[Modem support list] in the router's web interface for details. 2. Supports USB disk /FTP server. 3. Supports saving Syslog to USB disk. 4. Supports Policy Route (replacing Load Balance Rule and Address Mapping menus). 5. IPSec VPN tunnel can now be configured to pass or block NetBios packets. [Improvement] 1. Disabled HTTPS SSL 3.0 for CVE-2014-3566, this can be configured from the [System Maintenance] > [Management] page. 2. Connection request notifications from Vigor ACS were not authenticated 3. Could not establish IPv6 static connection. 4. Allow downloading/uploading private key (for Host to LAN VPN by X.509). 5. Shows the VPN Type/Form fields on VPN History web page. 6. Improved handling for Duplicated Routes (with Static Route Metric). When the static route metric is <=10, the priority of that static route will be greater than a VPN route. 7. Support QoS for VoIP traffic from LAN. 8. Support "Ping to Keep Alive" feature for detecting whether an IPsec tunnel is able to pass traffic 9. Support WAN Port and IP Alias options for PPTP Dial Out connections. 10. Support for RFC 4638 (accommodating an MTU/MRU larger than 1492 for PPPoE protocol WAN connections). 11. Added STUN server option to TR-069 settings. 12. Added Jumbo Frame setting under [LAN]-[Switch]-[Jumbo Frame] to edit Maximum Frame size. 13. Added a "Clear" button for the DDNS settings page. 14. Bind IP to MAC can now export or import a list of IP / MAC addresses. 15. [Sytem Maintenance] > [Access Control] can now be configured to accept pings from the WAN on specified WAN interfaces. 16. Added “OVH” as service provider for DDNS setting. 17. Supports Range-to-many Port Redirection. 18. Improve login page customization for Web Portal setup. 19. Changed mechanism of deleting objects. [Known Issue] 1. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in VPN and Remote Access >> PPP General Setup. 2. PN Trunk tunnel should not be used with a profile name over 15 characters. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.8.2 (Formal Release) Release Date : 15th August 2014 Build Date : 13th June 2014 Revision : r3968 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] None [Improvement] 1. PPTP connection stability improved 2. Web Portal stability improved 3. Improved: Remove management port setting which may occupy port redirection. 4. Improve the stability of High Availability function. 5. Add telnet timeout if login not completed in 60 seconds 6. CPU usage is too high when data flow monitor is enabled. 7. Improved interoperability with SSL VPN client 8. A problem of WCF license occurred when HA is enabled. 9. CVM can't perform configuration backup. 10. NAT Loopback to LAN More Subnet doesn’t work. 11. DNS for PPTP Remote dial-in is not assigned according to the LAN Profile. 12. Reboot with Customized Configurations bug. 13. When firewall default policy (block) is used, HTTP is still available for access. 14. Web portal still supports URL redirect when login mode is disabled. 15. Packet count error when PPTP acceleration is enabled. 16. mOTP User profile cannot be saved without Password. 17. WAN Priority Bits doesn’t work. 18. time object error corrected 19.[WAN]>[Switch mode]>[double tag] error corrected 20. Upgrade OpenSSL to 0.9.8za for security updates. 21. Update WCF (Web Content Filter) to account for Commtouch name change to Cyren. 22. High Availability improvements 23. DDNS failover 3G WAN improvements [Known Issue] 1. VPN Trunk tunnel doesn't work well when the profile name is more than 15 characters. 2. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in VPN and [Remote Access]>[PPP General Setup] ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.8 (Formal Release) Release Date : 11th March 2014 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] 1. Same WAN VLAN ID can be used in different WAN interfaces. (WAN >> General Setup Mode: Advance, Switch Mode: Double Tag) 2. QoS for multiple WANs. 3. SNMP v3. 4. Country block for Firewall. 5. WCF white list. 6. LAN DNS server. 7. BGP routing protocol. 8. SSL VPN in tunnel mode 9. Support Web Portal and Hotspot (Guest profile) in User Management. 10. Support PPTP acceleration for PPTP WAN/Remote Dial-in/LAN to LAN 11. QoS retag option added 12. VPN dial-out failover if WAN disconnected. 13. Support VPN LAN to LAN for overlap/duplicate subnets. 14. Display the last UP/DOWN log of VPN profile. 15. Add default policy for Firewall and default block policy can be applied. 16. Add IPv6 firewall settings. 17. Add DNS object. 18. Add a remote capture telnet command (rc), for traffic monitor and wireshark remote capture. 19. Add front panel and VPN status on the dashboard. [Improvements] Web User Interface changes 1. Menu [User Managemen]>[General Setup] renamed [User Management]>[Web Portal] 2. Move [IP Routing] from to [Routing]>[Status Route] and rename as [LAN/WAN Proxy ARP] 3. Move [Inter-LAN Route] to [LAN]>[General Setup] from [LAN]>[Static Route] 4. Move status page to the first tab of each function menu. Others 5. Support RADIUS, LDAP, Local authentication in User Management. 6. Support NAT option for IPsec LAN to LAN. 7. Support LDAP profile in Firewall. 8. Support ratio configuration for VPN Load Balancing. 9. Port number setting for Access Control in WAN IP alias can be passed to LAN by default. 10. Notification object can be recorded on Syslog through the configuration on [Applications]>[SMS/Mail Alert Service] 11. Support Local/RADIUS/LDAP authentication for PPTP/L2TP/PPPoE 12. Inter-LAN route priority changed so that IP filter can control 13. Support connection failover for TR-069. 14. Display router name in web page title. 15. IPsec VPN dial-in connection with all WANs is supported in default. 16. Support RFC3021. 17. Combine IM/P2P/Protocol object to App Object for blocking more Apps. 18. Management Access Control List increased up to 16 entries 19. Support peer identity for IPsec RSA authentication. 20. Support password encode option for configuration backup. 21. Support more special characters in username for user profile. 22. Number of SSL web proxy/VNC/RDP profiles increased to 30 23. Support customized DDNS. 24. Support acceleration of fragmented UDP packets (maximum 1628 bytes). 25. Support DHCP option 95 (LDAP server), 161(FTP server), and 162 (File path) 26. Support more subnet DHCP servers in Bind IP to MAC. 27. Support DHCP relay over LAN/Non-Direct-Connected LAN. 28. Support DHCP relay settings for PPTP/L2TP/PPPoE. 29. Support open port to the host in remote VPN network. 30. Default route cannot work well when two WAN IPs are in the same IP network. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.7.1 (Formal Release) Release Date : 13th November 2013 Build Date : 12th November 2013 Revision : r3067 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] None. [Improvement] 1. Support USB-WAN for WAN Profile under the Setting tab in Application>> Dynamic DNS. 2. Support WCF (web content filter) in High Availability (HA) application. 3. Modify the mechanism for IP filter, "if no further match" action. 4. Add a subnet mask setting, 255.255.255.254, for WAN IP configuration. 5. Added option disable negotiation for Fiber WAN under the Interface tab in WAN>>Switch. 6. ‘space’ special character can be used in the username for LDAP 7. QoS IP rule can apply the packets passing through both Local IP and Remote IP. 8. Improved PPTP service mechanism for multiple simultaneous LAN to LAN dial-ins 9. Corrected: Can not block / unblock some IPs on Diagnostics>>Data Flow Monitor. 10. Corrected issue with ICMP packets larger than 8138 bytes over IPSec LAN to LAN tunnel. 11. Corrected: The user can not access Internet when QoS queue weight is set as “0”. 12. Corrected: Lower the priority of Inter-LAN routing function. 13. Corrected: LAN DHCP packets do not respond while LAN DHCP Server is OFF. 14. Corrected: Can’t accept L2TP VPN from none default route WAN. 15. Corrected: RADIUS client (Vigor router) sends wrong NAS IP address (127.0.0.1). 16. Corrected traffic status of DHCP over IPsec in VPN Connection Management. 17. ARP detection may fail when WAN TX traffic is full. 18. Corrected: SMS can't be sent out when L2TP over IPsec is up and down. [Known Issue] 1. VPN Trunk tunnel doesn't work well when the profile name is more than 15 characters. 2. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in [VPN and Remote Access]>[PPP General Setup] ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.7 (Formal Release) Revision : 2733 Release Date : 2nd Sept 2013 Build Date : 27th Aug 2013 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] 1. Support Central VPN Management (CVM). Up to 16 devices can be managed. 2. Support 3G backup/load balance. 3. Support inbound load balance. 4. Support VPN Trunk failover mode. 5. Support PPPoE quota setting and MAC address filter. 6. Support USB temperature sensor. http://www.draytek.co.uk/products/usb-thermometer.html 7. Support SMS, Email Alert and Notification object profiles for WAN/VPN connection and USB temperature sensor. [Improvements] 1. Improved: Support SmartMonitor users up to 500. 2. Improved: VPN Trunk throughput and stability. 3. Improved: By default disable insecure SSL Encryption Key Algorithms 4. Improved: Support DHCP relay on VPN. 5. Improved: Add Active Standby mode for High Availability (HA). 6. Improved: QoS redesigned 7. Improved: Username reported to Syslog 8. Improved: Add option 60(Vendor ID), 61(Client ID) for WAN DHCP mode. 9. Improved: Add default maximum session number for Session limit. 10. Improved: Add flow control settings for Switch. 11. Improved: Add user defined options for DHCP server. 12. Improved: Improve DMZ function. 13. Improved: Add log and force update function for DDNS. 14. Improved: Add Force L2TP with IPsec policy option enabled in default. 15. Improved: Corrected causes for high CPU usage being displayed in Web UI 16. Improved: Stability in TR-069. 17. Improved: Firmware upgrade speed. 18. Fixed: Time object cannot work correctly when daylight saving is enabled. [Known Issue] 1. VPN Trunk tunnel doesn't work well when the profile name is more than 15 characters. 2. You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in [VPN and Remote Access]>[PPP General Setup] ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.6.1 (Formal Release) Release Date : 10th April 2013 Build Date : 25th March 2013 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] None [Improvements] 1. NAT Port Redirection Rule for FTP server didn't work with two WAN connection 2. Customized web content message would disappear after rebooting the router 3. Improvements to VPN Trunk tunnel where profile name are long 4. PPTP connection display error in VPN Graph for syslog utility 5. PPTP WAN could not dial-up if the server was set with a domain name 6. Fixed issue with ping to VPN remote network working after clicking WAN DHCP Renew Button via web user interface 7. Fixed Session limit rule notapplying the correct limit due to subnet mask caculation error 8. Fixed that WAN status displays “up” when the WAN cable is unplugged and WAN detect mode is set with “None” 9. Corrected an issue with SNMP set/get Community setting 10. Resolved that VPN traffic wouldn't flow while one of the VPN GRE tunnels is disconnected 11. Corrected issue preventing some vLAN users from accessing Internet via Browser 12. Improved DHCP renewal interoperability 13. Fixed LAN VLAN configuration issues after restoring the web configuration 14. Corrected WAN1 MAC address used 15. Improved SIP ALG feature 16. Fixed that IPSec tunnel uptime would not reset after VPN reconnection 17. Corrected PPTP sessions problem that would prevent new network connections being setup 18. Corrected that a PC from remote subnet could't access Internet via PPTP LAN to LAN tunnel 19. Improvments to IPv6 traffic handling via AICCU 20. Improved load balance where multiple PPPoE connections have the same gateway 21. Corrected issue where multiple WAN disconnections could prevent VPN Trunk from reconnecting 22. Added information for remote network connected with GRE over IPsec to Routing Table 23. Corrected issue where enabling Perfect Forward Secrecy in VPN client could prevent connection 24. Display issue with transmitted/received (TX/ RX) packets in Connection Management fixed for VPN clients behind NAT 25. Improved parameters stability for TR-069 26. Improved throughput between different VLANs 27. Added sending ARP for WAN Alias IP to WAN Gateway when connected 28. Added support for VPN on Alias WAN IP and IP Routing IP 29. Add mail alert when VPN is up 30. High availability improvements [Known Issues] 1. VPN Trunk tunnel profile names should be kept to less than 15 characters. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.6 (Formal Release) Release Date : 2nd Jan 2013 Build Date : 6th Nov 2012 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** [New Features] 1. VPN(IPSEC) Routing Acceleration 2. Supports PPPoE server for LAN PC connection 3. Support VPN Alarm via E-mail & Syslog 4. Support VPN Graph for syslog utility 5. Support PPP mode for IPv6 6. Support domain name for IPSec/PPTP dial-out [Improvements] 1. URL filter can block HTTPS connection by host keyword 2. WCF support https block by web category 3. Add QQ account filter for Firewall 4. WAN4 is regarded as physical DMZ port 5. Add time schedule for session limit and bandwidth limit 6. Web content filter (WCF) stability improvements 7. Data flow monitor resource allocation improvements 8. DHCP server cannot work when Multi-LANs is configured 9. Hosts under routing LAN can not access into the router 10. Configuration backup may fail 11. UPnP improved 12. Changing web port could prevent User management from working 13. WebUI server security improvements 14. IPsec RX/TX packets count may have error after entering phase2 rekey 15. L2TP connection status error after disconnection. 16 Cannot create IPsec VPN in aggressive mode when selecting AES as IKE phase 1 encryption. 17. PPTP dial-in may fail while using static IP mode. 18. VPN load balance may not work after connection reconnects 19. SSL Application doesn't work when HTTPS port is not set with 443. 20. Support PPTP dial on demand and idle timeout. 21. Support URL filter rules move up/down. 22. Support VLAN priority in LAN/WAN interface. 23. Support QoS packet by DiffServ (DSCP/TOS) for outgoing packet. 24. Let the user profile password support more special characters in standard ASCII table. 25. Show the IP binding with MAC in DHCP table. 26. Mail Alert Send test e-mail button added 27. Add 36 regions time zone options for NTP. 28. Improve user management login process. 29. Add Common Name Identifier field in LDAP configuration. 30. Add an option for DDNS to select Internet IP or WAN IP. [Known Issue] 1. VPN Trunk tunnel profile names must be less than 15 characters. ********************************************************************** Release Notes for Vigor 3900 Firmware Version : 1.0.5 (Formal Release) Release Date : 4th Sept 2012 Applicable Models : Vigor 3900 Locale : UK ONLY ********************************************************************** First Firmware Release [Known Issues] - Devices on non-NAT subnets are unable to access the routers management interface [END OF FILE]